Best for: Homeowners, contractors, grounds teams and designers comparing water sources before selecting pumps, storage or treatment.
Start with demand, not the pump
Estimate peak daily and seasonal irrigation demand, required flow, operating pressure and acceptable downtime. Then test whether the source can supply that duty during the driest credible period.
| Source | Potential advantage | Main checks |
|---|---|---|
| Mains water | Convenient and usually consistent quality | Available running flow and pressure, restrictions, backflow protection and cost. |
| Harvested rainwater | Captures water already falling on the site | Roof yield, storage balance, water quality, filtration, overflow and backup. |
| Borehole or well | Can provide an independent source | Consent and licensing, sustainable yield, drawdown, chemistry, bore construction and pump duty. |
| Pond, lake, river or stream | Can support larger sites where lawfully available | Abstraction authorisation, seasonal level and flow, ecology, intake screening, sediment and algae. |
| Delivered or transferred water | Emergency or supplementary option | Source legality, quality, storage hygiene, access, cost and transfer capacity. |

Five questions every source must answer
- Quantity: what is reliably available each day and season?
- Quality: what treatment is required for the crop and equipment?
- Legality: what permission, licence, notification or land access is required?
- Hydraulics: what lift, pipe loss, flow and pressure must the pump overcome?
- Resilience: what happens during drought, contamination, pump failure or a hosepipe restriction?
Direct supply or storage?
Use direct supply only when the source can maintain the complete irrigation duty for the longest required operating period at the lowest credible source condition. Check sustained flow and level, water quality, permission, total dynamic head, pump operating point, intake or suction limits, filtration and the response to source or power failure.
Storage can let a lower-rate source refill over a longer period while a separate irrigation pump serves a higher peak zone flow. Size it from a time-step water balance, not from daily demand alone. Storage does not create water or override a licence, hands-off-flow condition, borehole sustainable yield or treatment limit.
| Arrangement | Source test | Design consequence |
|---|---|---|
| Direct | Source sustains peak irrigation flow for the full cycle. | One hydraulic duty, but source variation acts directly on irrigation performance. |
| Source to storage | Source volume is adequate over time even if its flow is below the irrigation peak. | Separate transfer and irrigation pump duties, storage balance, level control and overflow. |
| Hybrid | Every mode and permission is defined. | Cause-and-effect logic, backflow protection, isolation and failure-state testing are essential. |
Do not combine sources casually
Mains water must not be directly connected to an alternative source. Where both are used, provide the legally appropriate separation and notify the relevant water undertaker where required. Clearly identify non-potable services.
Information for selection
- Site and jurisdiction.
- Source type, ownership and permissions.
- Measured source level or inlet pressure under operating conditions.
- Expected daily and annual demand.
- Water analysis and visible solids.
- Distance, elevation and proposed pipe size.
- Required storage, backup and control philosophy.
- Longest irrigation cycle, refill window and the dependable source rate during each period.
- For storage: nominal and usable volume, low/high operating levels, dead storage, overflow route and required reserve.
A full tank can hide a refill shortfall
Keep the source and storage separate. A tank or reservoir holds water; its refill rate determines how quickly that water is replaced.
Hypothetical example: a refill meter increases by 10 cubic metres over two hours. This is 5 cubic metres an hour. If that rate were sustained for 24 hours, it would add 120 cubic metres. A 200 cubic metre watering night would leave an 80 cubic metre daily shortfall. Stored water may cover it temporarily, but the source would not replenish it at that rate.
This arithmetic illustration is adapted from John Kidson’s internal article on irrigation water sources. It is not a measured client result or a guarantee of year-round borehole output. Check actual operating rates, seasonal behaviour and permissions.
Considering groundwater? Read our borehole and well guide, including how to use free nearby BGS records before discussing drilling with a specialist.
Related Irri Hub guides
- Boreholes and wells for irrigation
- UK water abstraction rules
- Irrigation water quality testing
- Which irrigation pump do I need?
Sources and limitations
See the relevant environmental regulator and Water Regs UK alternative-water guidance. Site conditions, permissions and water quality control the final design.