Irrigation Field Cable Records and Buried Joints

Scope: Low-voltage irrigation control and decoder records. Mains-voltage work remains outside this guide.

Cable schedule

  • Cable type, conductor size and manufacturer.
  • Controller, route, start and end points.
  • Station, common and spare conductor identities.
  • Decoder address, type and protected device where applicable.
  • Joint reference, location and enclosure method.
  • Measured test results and test conditions.

Record a decoder replacement before burial

Record the manufacturer, full model, factory label and actual programmed address where applicable, the station or solenoid served, joint reference, location and test result. Photograph old and new labels safely before the replacement is concealed, then update the controller, station schedule and drawing with the date and revision. Protect any private site information when sharing the record.

Rain Bird’s legacy Decoder System Manual describes factory-assigned addresses for its listed FD-series devices and separate programming names for the areas they serve. Some addresses in that system can be reprogrammed. This is an example of why the installed identity and software mapping matter; it does not establish compatibility of another decoder from its appearance.

Two Rain Bird FD-101 irrigation field decoders shown side by side with address codes obscured
JK Irrigation photograph: two Rain Bird FD-101 field decoders, one cleaner and one weathered. Similar markings do not establish programming, compatibility, test condition or installation status. Address codes have been obscured in this web copy.

Route design

Coordinate with water pipes, mains electricity, communications, drainage and other buried services. Follow required separation and crossing details. Provide mechanical protection where the risk assessment requires it.

Blue irrigation control cable and black pipework following an open trench route
JK Irrigation photograph: blue control cable and black irrigation pipework follow an open trench route before backfilling. The photograph does not establish burial depth, separation from other services, cable type or the final as-fitted route.

Buried joints

Use the controller and cable manufacturer’s specified connection system for the environment. A connector described casually as “waterproof” may depend on conductor size, preparation, orientation, gel or resin, enclosure and installation technique.

Voltage drop

Long cable runs and simultaneous loads can reduce voltage at the solenoid or decoder. Calculate using the actual circuit length, conductor resistance, load current and permitted device voltage. Remember that a common conductor may carry combined return current.

Testing boundary

Record resistance, insulation or decoder tests only when performed with equipment suitable for the connected devices and by a competent person. Some electronic equipment can be damaged by an inappropriate test voltage.

As-fitted record

Locate joints by measured offsets, not memory. Photograph the open joint before burial and link the photograph to the drawing reference.

Cable and jointing examples

These live examples show the kinds of components that may appear on a field-cable schedule. They are not interchangeable: conductor material and size, insulation diameter, controller requirements, burial environment and the connector manufacturer’s installation method must all be checked.

Two-core 2.5 square millimetre irrigation decoder cable

Field-cable example

2-Core 2.5 mm² Irrigation Decoder Cable

Representative reference SKU IRRI-CABLE-250M is the 250 m drum. Record the installed length and retain the exact system approval.

View decoder cable length options

3M DBR/Y-6 direct-bury splice kit

Direct-burial joint example

3M Direct Bury Splice Kit DBR/Y-6

Representative individual kit SKU DBR/Y-6 1. Verify the wire range and complete installation method for the actual circuit.

View the 3M direct-bury splice kit

3M 314 moisture-resistant irrigation cable connector

Cable-connector example

3M 314 Waterproof Cable Connector

Catalogue reference SKU 31CM31401. Confirm conductor size, number of conductors, enclosure and environmental requirements.

View the 3M 314 cable connector

See currently available cable and connection products · Read the low-voltage fault guide · Read the golf cable-rewire overview

Related guides

Browse by brand Rain Bird

Sources and limitations

This guide supports planning and record keeping. The final design must follow current manufacturer instructions, site risk assessments, legal duties, water-undertaker requirements and applicable standards. Relevant references include HSE HSG47, Water Regs UK backflow guidance and BS EN 805:2025.